Rep. Norm Thurston — Voting Record

Utah House District 62 · complete roll-call record from le.utah.gov
← All votes

Bill

Local Land Use Amendments
Number
H.B. 127 First Substitute (2015GS)
Sponsor
Rep. Peterson, J.
Final action
Governor Signed 3/26/2015
Outcome
Became law — signed by Gov. Gary R. Herbert

Summary

This bill amends land use provisions in the municipal, county, and State Construction Code.

What it does

  • This bill:
  • defines "rental dwelling";
  • prohibits, with certain exceptions, a municipality or county from requiring physical changes to a legal nonconforming rental dwelling use;
  • prohibits a municipality or county from requiring physical changes to install an egress or emergency escape window in certain circumstances; and
  • amends bedroom window egress provisions in the State Construction Code.

Every vote on this bill

2/20/2015House/ passed 3rd reading
Senate Secretary
62 6 7YEA
3/5/2015Senate/ passed 2nd reading
Senate 3rd Reading Calendar
21 0 8not eligible / no record
3/6/2015Senate/ circled
Senate 3rd Reading Calendar
Voice votenot eligible / no record
3/6/2015Senate/ uncircled
Senate 3rd Reading Calendar
Voice votenot eligible / no record
3/6/2015Senate/ passed 3rd reading
Senate President
25 0 4not eligible / no record

Bill text

enrolled version · official source
LOCAL LAND USE AMENDMENTS
GENERAL SESSION
STATE OF UTAH
Chief Sponsor: Jeremy A. Peterson
Senate Sponsor: 
Curtis S. Bramble
LONG TITLE
General Description:
This bill amends land use provisions in the municipal, county, and State Construction
Code.
Highlighted Provisions:
This bill:
▸ defines "rental dwelling";
▸ prohibits, with certain exceptions, a municipality or county from requiring physical
changes to a legal nonconforming rental dwelling use;
▸ prohibits a municipality or county from requiring physical changes to install an
egress or emergency escape window in certain circumstances; and
▸ amends bedroom window egress provisions in the State Construction Code.
Money Appropriated in this Bill:
None
Other Special Clauses:
None
Utah Code Sections Affected:
AMENDS:
10-9a-511
, as last amended by Laws of Utah 2012, Chapter 289
15A-3-202
, as last amended by Laws of Utah 2013, Chapter 297
ENACTS:
10-9a-511.5
, Utah Code Annotated 1953
17-27a-510.5
, Utah Code Annotated 1953
Be it enacted by the Legislature of the state of Utah:
Section 1. Section 
10-9a-511
 is amended to read:
10-9a-511.
Nonconforming uses and noncomplying structures.
(1) (a) Except as provided in this section, a nonconforming use or noncomplying
structure may be continued by the present or a future property owner.
(b) A nonconforming use may be extended through the same building, provided no
structural alteration of the building is proposed or made for the purpose of the extension.
(c) For purposes of this Subsection (1), the addition of a solar energy device to a
building is not a structural alteration.
(2) The legislative body may provide for:
(a) the establishment, restoration, reconstruction, extension, alteration, expansion, or
substitution of nonconforming uses upon the terms and conditions set forth in the land use
ordinance;
(b) the termination of all nonconforming uses, except billboards, by providing a
formula establishing a reasonable time period during which the owner can recover or amortize
the amount of his investment in the nonconforming use, if any; and
(c) the termination of a nonconforming use due to its abandonment.
(3) (a) A municipality may not prohibit the reconstruction or restoration of a
noncomplying structure or terminate the nonconforming use of a structure that is involuntarily
destroyed in whole or in part due to fire or other calamity unless the structure or use has been
abandoned.
(b) A municipality may prohibit the reconstruction or restoration of a noncomplying
structure or terminate the nonconforming use of a structure if:
(i) the structure is allowed to deteriorate to a condition that the structure is rendered
uninhabitable and is not repaired or restored within six months after written notice to the
property owner that the structure is uninhabitable and that the noncomplying structure or
nonconforming use will be lost if the structure is not repaired or restored within six months; or
(ii) the property owner has voluntarily demolished a majority of the noncomplying
structure or the building that houses the nonconforming use.
(c) (i) Notwithstanding a prohibition in its zoning ordinance, a municipality may
permit a billboard owner to relocate the billboard within the municipality's boundaries to a
location that is mutually acceptable to the municipality and the billboard owner.
(ii) If the municipality and billboard owner cannot agree to a mutually acceptable
location within 90 days after the owner submits a written request to relocate the billboard, the
provisions of Subsection 
10-9a-513
(2)(a)(iv) apply.
(4) (a) Unless the municipality establishes, by ordinance, a uniform presumption of
legal existence for nonconforming uses, the property owner shall have the burden of
establishing the legal existence of a noncomplying structure or nonconforming use.
(b) Any party claiming that a nonconforming use has been abandoned shall have the
burden of establishing the abandonment.
(c) Abandonment may be presumed to have occurred if:
(i) a majority of the primary structure associated with the nonconforming use has been
voluntarily demolished without prior written agreement with the municipality regarding an
extension of the nonconforming use;
(ii) the use has been discontinued for a minimum of one year; or
(iii) the primary structure associated with the nonconforming use remains vacant for a
period of one year.
(d) The property owner may rebut the presumption of abandonment under Subsection
(4)(c), and shall have the burden of establishing that any claimed abandonment under
Subsection (4)(b) has not in fact occurred.
(5) A municipality may terminate the nonconforming status of a school district or
charter school use or structure when the property associated with the school district or charter
school use or structure ceases to be used for school district or charter school purposes for a
period established by ordinance.
[
(6) A municipal ordinance adopted under Section 
10-1-203.5
 may not:
]
[
(a) require physical changes in a structure with a legal nonconforming rental housing
use unless the change is for:
]
[
(i) the reasonable installation of:
]
[
(A) a smoke detector that is plugged in or battery operated;
]
[
(B) a ground fault circuit interrupter protected outlet on existing wiring;
]
[
(C) street addressing;
]
[
(D) except as provided in Subsection (7), an egress bedroom window if the existing
bedroom window is smaller than that required by current state building code;
]
[
(E) an electrical system or a plumbing system, if the existing system is not functioning
or is unsafe as determined by an independent electrical or plumbing professional who is
licensed in accordance with Title 58, Occupations and Professions;
]
[
(F) hand or guard rails; or
]
[
(G) occupancy separation doors as required by the International Residential Code; or
]
[
(ii) the abatement of a structure; or
]
[
(b) be enforced to terminate a legal nonconforming rental housing use.
]
[
(7) A municipality may not require a change described in Subsection (6)(a)(i)(D) if the
change:
]
[
(a) would compromise the structural integrity of a building; or
]
[
(b) could not be completed in accordance with current building codes, including
set-back and window well requirements.
]
[
(8) A legal nonconforming rental housing use may not be terminated under Section
10-1-203.5
.
]
Section 2. Section 
10-9a-511.5
 is enacted to read:
 10-9a-511.5.
Changes to dwellings -- Egress windows.
(1) For purposes of this section, "rental dwelling" means the same as that term is
defined in Section 
10-8-85.5
.
(2) A municipal ordinance adopted under Section 
10-1-203.5
 may not:
(a) require physical changes in a structure with a legal nonconforming rental dwelling
use unless the change is for:
(i) the reasonable installation of:
(A) a smoke detector that is plugged in or battery operated;
(B) a ground fault circuit interrupter protected outlet on existing wiring;
(C) street addressing;
(D) except as provided in Subsection (3), an egress bedroom window if the existing
bedroom window is smaller than that required by current State Construction Code;
(E) an electrical system or a plumbing system, if the existing system is not functioning
or is unsafe as determined by an independent electrical or plumbing professional who is
licensed in accordance with Title 58, Occupations and Professions;
(F) hand or guard rails; or
(G) occupancy separation doors as required by the International Residential Code; or
(ii) the abatement of a structure; or
(b) be enforced to terminate a legal nonconforming rental dwelling use.
(3) A municipality may not require physical changes to install an egress or emergency
escape window in an existing bedroom that complied with the State Construction Code in
effect at the time the bedroom was finished if:
(a) the dwelling is an owner-occupied dwelling or a rental dwelling that is:
(i) a detached one-, two-, three-, or four-family dwelling; or
(ii) a town home that is not more than three stories above grade with a separate means
of egress; and
(b) (i) the window in the existing bedroom is smaller than that required by current State
Construction Code; and
(ii) the change would compromise the structural integrity of the structure or could not
be completed in accordance with current State Construction Code, including set-back and
window well requirements.
(4) Nothing in this section prohibits a municipality from:
(a) regulating the style of window that is required or allowed in a bedroom;
(b) requiring that a window in an existing bedroom be fully openable if the openable
area is less than required by current State Construction Code; or
(c) requiring that an existing window not be reduced in size if the openable area is
smaller than required by current State Construction Code.
Section 3. Section 
15A-3-202
 is amended to read:
15A-3-202.
Amendments to Chapters 1 through 5 of IRC.
(1) In IRC, Section R102, a new Section R102.7.2 is added as follows: "R102.7.2
Physical change for bedroom window egress [
in legal nonconforming rental housing use
]. A
structure [
classified as a legal nonconforming rental housing use,
] whose egress [
bedroom
]
window 
in an existing bedroom
 is smaller than required by this code, 
and that complied with
the construction code in effect at the time that the bedroom was finished,
 is not required to
undergo a physical change to conform to this code if the change would compromise the
structural integrity of the [
building
] 
structure
 or could not be completed in accordance with
other applicable requirements of this code, including setback and window well requirements."
(2) In IRC, Section 109:
(a) A new IRC, Section 109.1.5, is added as follows: "R109.1.5 Weather-resistant
exterior wall envelope inspections. An inspection shall be made of the weather-resistant
exterior wall envelope as required by Section R703.1 and flashings as required by Section
R703.8 to prevent water from entering the weather-resistive barrier."
(b) The remaining sections are renumbered as follows: R109.1.6 Other inspections;
R109.1.6.1 Fire- and smoke-resistance-rated construction inspection; R109.1.6.2 Reinforced
masonry, insulating concrete form (ICF) and conventionally formed concrete wall inspection;
and R109.1.7 Final inspection.
(3) IRC, Section R114.1, is deleted and replaced with the following: "R114.1 Notice to
owner. Upon notice from the building official that work on any building or structure is being
prosecuted contrary to the provisions of this code or other pertinent laws or ordinances or in an
unsafe and dangerous manner, such work shall be immediately stopped. The stop work order
shall be in writing and shall be given to the owner of the property involved, or to the owner's
agent or to the person doing the work; and shall state the conditions under which work will be
permitted to resume."
(4) In IRC, Section R202, the following definition is added: "CERTIFIED
BACKFLOW PREVENTER ASSEMBLY TESTER: A person who has shown competence to
test Backflow prevention assemblies to the satisfaction of the authority having jurisdiction
under Utah Code, Subsection 
19-4-104
(4)."
(5) In IRC, Section R202, the definition for "CONDITIONED SPACE" is modified by
deleting the words at the end of the sentence "being heated or cooled by any equipment or
appliance" and replacing them with the following: "enclosed within the building thermal
envelope that is directly heated or cooled, or indirectly heated or cooled by any of the following
means:
1. Openings directly into an adjacent conditioned space.
2. An un-insulated floor, ceiling or wall adjacent to a conditioned space.
3. Un-insulated duct, piping or other heat or cooling source within the space."
(6) In IRC, Section R202, the definition of "Cross Connection" is deleted and replaced
with the following: "CROSS CONNECTION. Any physical connection or potential
connection or arrangement between two otherwise separate piping systems, one of which
contains potable water and the other either water of unknown or questionable safety or steam,
gas, or chemical, whereby there exists the possibility for flow from one system to the other,
with the direction of flow depending on the pressure differential between the two systems (see
"Backflow, Water Distribution")."
(7) In IRC, Section 202, in the definition for gray water a comma is inserted after the
word "washers"; the word "and" is deleted; and the following is added to the end: "and clear
water wastes which have a pH of 6.0 to 9.0; are non-flammable; non-combustible; without
objectionable odors; non-highly pigmented; and will not interfere with the operation of the
sewer treatment facility."
(8) In IRC, Section R202, the definition of "Potable Water" is deleted and replaced
with the following: "POTABLE WATER. Water free from impurities present in amounts
sufficient to cause disease or harmful physiological effects and conforming to the Utah Code,
Title 19, Chapters 4, Safe Drinking Water Act, and 5, Water Quality Act, and the regulations of
the public health authority having jurisdiction."
(9) IRC, Figure R301.2(5), is deleted and replaced with Table R301.2(5a) and Table
R301.2(5b) as follows:
"TABLE NO. R301.2(5a)
STATE OF UTAH - REGIONAL SNOW LOAD FACTORS
COUNTY
P
o
S
A
o
Beaver
6.2
Box Elder
5.2
Cache
4.5
Carbon
5.2
Daggett
6.5
Davis
4.5
Duchesne
6.5
Emery
6.0
Garfield
6.0
Grand
6.5
Iron
5.8
Juab
5.2
Kane
5.7
Millard
5.3
Morgan
4.5
Piute
6.2
Rich
4.1
Salt Lake
4.5
San Juan
6.5
Sanpete
5.2
Sevier
6.0
Summit
5.0
Tooele
4.5
Uintah
7.0
Utah
4.5
Wasatch
5.0
Washington
6.0
Wayne
6.5
Weber
4.5
TABLE NO. R301.2(5b)
REQUIRED SNOW LOADS FOR SELECTED UTAH CITIES AND TOWNS
1,2
The following jurisdictions require design snow load values that differ from the Equation in
the Utah Snow Load Study.
County
City
Elevation
Ground Snow
Load (psf)
Roof Snow
Load (psf)
Carbon
Price
All other county locations
--
--
--
Davis
Fruit Heights
- 4850
Emery
Green River
Garfield
Panguitch
Rich
Woodruff
Laketown
Garden City
Randolph
--
--
--
San Juan
Monticello
Summit
Coalville
Kamas
Tooele
Tooele
Utah
Orem
Pleasant Grove
Provo
--
--
--
Wasatch
Heber
--
--
--
Washington
Leeds
Santa Clara
St. George
All other county locations
--
--
--
Wayne
Loa
The IRC requires a minimum live load -- See R301.6.
This table is informational only in that actual site elevations may vary. Table is only valid
if site elevation is within 100 feet of the listed elevation. Otherwise, contact the local
Building Official.
Values adopted from Table VII of the Utah Snow Load Study
Values based on site-specific study. Contact local Building Official for additional
information.
Contact local Building Official.
Based on C
e
 =1.0, C
t
 =1.0 and I
s
 =1.0"
(10) IRC, Section R301.6, is deleted and replaced with the following: "R301.6 Utah
Snow Loads. The snow loads specified in Table R301.2(5b) shall be used for the jurisdictions
identified in that table. Otherwise, the ground snow load, P
g
, to be used in the determination of
design snow loads for buildings and other structures shall be determined by using the following
formula: P
g
 = (P
o
 + S
(A-A
o
)
)
0.5
 for A greater than A
o
, and P
g
 = P
o
 for A less than or equal to
A
o
.
WHERE:
P
g
 = Ground snow load at a given elevation (psf);
P
o
 = Base ground snow load (psf) from Table No. R301.2(5a);
S = Change in ground snow load with elevation (psf/100 ft.) From Table No. R301.2(5a);
A = Elevation above sea level at the site (ft./1,000);
A
o
 = Base ground snow elevation from Table R301.2(5a) (ft./1,000).
The building official may round the roof snow load to the nearest 5 psf. The ground snow
load, P
g
, may be adjusted by the building official when a licensed engineer or architect submits
data substantiating the adjustments.
Where the minimum roof live load in accordance with Table R301.6 is greater than the design
roof snow load, such roof live load shall be used for design, however, it shall not be reduced to
a load lower than the design roof snow load. Drifting need not be considered for roof snow
loads less than 20 psf."
(11) In IRC, Section R302.2, the words "Exception: A" are deleted and replaced with
the following:
"Exceptions:
1. A common 2-hour fire-resistance-rated wall is permitted for townhouses if such walls do
not contain plumbing or mechanical equipment, ducts or vents in the cavity of the common
wall. Electrical installation shall be installed in accordance with Chapters 34 through 43. 
Penetrations of electrical outlet boxes shall be in accordance with Section R302.4.
2. In buildings equipped with an automatic residential fire sprinkler system, a".
(12) In IRC, Section R302.2.4, a new exception 6 is added as follows: "6. Townhouses
separated by a common 2-hour fire-resistance-rated wall as provided in Section R302.2."
(13) In IRC, Section R302.5.1, the words "self-closing device" are deleted and replaced
with "self-latching hardware".
(14) In IRC, Section R303.4, the number "5" is changed to "3" in the first sentence.
(15) IRC, Sections R311.7.4 through R311.7.4.3, are deleted and replaced with the
following: "R311.7.4 Stair treads and risers. R311.7.4.1 Riser height. The maximum riser
height shall be 8 inches (203 mm). The riser shall be measured vertically between leading
edges of the adjacent treads. The greatest riser height within any flight of stairs shall not
exceed the smallest by more than 3/8 inch (9.5 mm).
R311.7.4.2 Tread depth. The minimum tread depth shall be 9 inches (228 mm). The tread
depth shall be measured horizontally between the vertical planes of the foremost projection of
adjacent treads and at a right angle to the tread's leading edge. The greatest tread depth within
any flight of stairs shall not exceed the smallest by more than 3/8 inch (9.5 mm). Winder
treads shall have a minimum tread depth of 10 inches (254 mm) measured as above at a point
12 inches (305 mm) from the side where the treads are narrower. Winder treads shall have a
minimum tread depth of 6 inches (152 mm) at any point. Within any flight of stairs, the
greatest winder tread depth at the 12-inch (305 mm) walk line shall not exceed the smallest by
more than 3/8 inch (9.5 mm).
R311.7.4.3 Profile. The radius of curvature at the leading edge of the tread shall be no greater
than 9/16 inch (14.3 mm). A nosing not less than 3/4 inch (19 mm) but not more than 1 1/4
inches (32 mm) shall be provided on stairways with solid risers. The greatest nosing projection
shall not exceed the smallest nosing projection by more than 3/8 inch (9.5 mm) between two
stories, including the nosing at the level of floors and landings. Beveling of nosing shall not
exceed 1/2 inch (12.7 mm). Risers shall be vertical or sloped from the underside of the leading
edge of the tread above at an angle not more than 30 degrees (0.51 rad) from the vertical. Open
risers are permitted, provided that the opening between treads does not permit the passage of a
4-inch diameter (102 mm) sphere.
Exceptions.
1. A nosing is not required where the tread depth is a minimum of 10 inches (254 mm).
2. The opening between adjacent treads is not limited on stairs with a total rise of 30 inches
(762 mm) or less."
(16) In IRC, Section R312.1.2, the words "adjacent fixed seating" are deleted.
(17) IRC, Section R312.2, is deleted.
(18) IRC, Sections R313.1 through R313.2.1, are deleted and replaced with the
following: "R313.1 Design and installation. When installed, automatic residential fire
sprinkler systems for townhouses or one- and two-family dwellings shall be designed and
installed in accordance with Section P2904."
(19) A new IRC, Section R315.5, is added as follows: "R315.5 Power source. Carbon
monoxide alarms shall receive their primary power from the building wiring when such wiring
is served from a commercial source, and when primary power is interrupted, shall receive
power from a battery. Wiring shall be permanent and without a disconnecting switch other
than those required for over-current protection.
Exceptions:
1. Carbon monoxide alarms shall be permitted to be battery operated when installed in
buildings without commercial power.
2. Hard wiring of carbon monoxide alarms in existing areas shall not be required where the
alterations or repairs do not result in the removal of interior wall or ceiling finishes exposing
the structure, unless there is an attic, crawl space or basement available which could provide
access for hard wiring, without the removal of interior finishes."
(20) A new IRC, Section R315.6, is added as follows: "R315.6 Interconnection. 
Where more than one carbon monoxide alarm is required to be installed within an individual
dwelling unit in accordance with Section R315.1, the alarm devices shall be interconnected in
such a manner that the actuation of one alarm will activate all of the alarms in the individual
unit. Physical interconnection of smoke alarms shall not be required where listed wireless
alarms are installed and all alarms sound upon activation of one alarm.
Exception: Interconnection of carbon monoxide alarms in existing areas shall not be required
where alterations or repairs do not result in removal of interior wall or ceiling finishes exposing
the structure, unless there is an attic, crawl space or basement available which could provide
access for interconnection without the removal of interior finishes."
(21) In IRC, Section R403.1.6, a new Exception 4 is added as follows: "4. When
anchor bolt spacing does not exceed 32 inches (813 mm) apart, anchor bolts may be placed
with a minimum of two bolts per plate section located not less than 4 inches (102 mm) from
each end of each plate section at interior bearing walls, interior braced wall lines, and at all
exterior walls."
(22) In IRC, Section R403.1.6.1, a new exception is added at the end of Item 2 and
Item 3 as follows: "Exception: When anchor bolt spacing does not exceed 32 inches (816 mm)
apart, anchor bolts may be placed with a minimum of two bolts per plate section located not
less than 4 inches (102 mm) from each end of each plate section at interior bearing walls,
interior braced wall lines, and at all exterior walls."
(23) In IRC, Section R404.1, a new exception is added as follows: "Exception: As an
alternative to complying with Sections R404.1 through R404.1.5.3, concrete and masonry
foundation walls may be designed in accordance with IBC Sections 1807.1.5 and 1807.1.6 as
amended in Section 1807.1.6.4 and Table 1807.1.6.4 under these rules."
(24) IRC, Section R501.3, is deleted.
Section 4. Section 
17-27a-510.5
 is enacted to read:
 17-27a-510.5.
Changes to dwellings -- Egress windows.
(1) For purposes of this section, "rental dwelling" means the same as that term is
defined in Section 
10-8-85.5
.
(2) A county ordinance adopted under Section 
10-1-203.5
 may not:
(a) require physical changes in a structure with a legal nonconforming rental dwelling
use unless the change is for:
(i) the reasonable installation of:
(A) a smoke detector that is plugged in or battery operated;
(B) a ground fault circuit interrupter protected outlet on existing wiring;
(C) street addressing;
(D) except as provided in Subsection (3), an egress bedroom window if the existing
bedroom window is smaller than that required by current State Construction Code;
(E) an electrical system or a plumbing system, if the existing system is not functioning
or is unsafe as determined by an independent electrical or plumbing professional who is
licensed in accordance with Title 58, Occupations and Professions;
(F) hand or guard rails; or
(G) occupancy separation doors as required by the International Residential Code; or
(ii) the abatement of a structure; or
(b) be enforced to terminate a legal nonconforming rental dwelling use.
(3) A county may not require physical changes to install an egress or emergency escape
window in an existing bedroom that complied with the State Construction Code in effect at the
time the bedroom was finished if:
(a) the dwelling is an owner-occupied dwelling or a rental dwelling that is:
(i) a detached one-, two-, three-, or four-family dwelling; or
(ii) a town home that is not more than three stories above grade with a separate means
of egress; and
(b) (i) the window in the existing bedroom is smaller than that required by current State
Construction Code; and
(ii) the change would compromise the structural integrity of the structure or could not
be completed in accordance with current State Construction Code, including set-back and
window well requirements.
(4) Nothing in this section prohibits a county from:
(a) regulating the style of window that is required or allowed in a bedroom;
(b) requiring that a window in an existing bedroom be fully openable if the openable
area is less than required by current State Construction Code; or
(c) requiring that an existing window not be reduced in size if the openable area is
smaller than required by current State Construction Code.